|
Technical Specification
Mains connection
Voltage: 1-phase and 3-lphase, 200 to 240 V, ±10% (ACS 100,
ACS140)
3-phase, 380 to 480 V, ±10% (ACS140, ACS 400)
Frequency : 48 to 63 Hz
Power Factor : approx. 0.98
Motor connection
Voltage : 3-phase, from 0 to Usupply
Frequency : ACS 100/140 : 0 to 300 Hz,
ACS 400 : 0 to 250 Hz
Continuous loading capability Zconstant torque at a max. ambient
temperature of 40 ◦C):
Rated output current I2.
Overload capacity (at a max. ambient temp. of 40◦C):
- at constant torque 1.5 x I2N, for 1 minute every 10 minutes
- at constant torque 1.25 x I2N, for 2 minutes every 10 minutes
Characteristic data for short-time, intermittent and periodic load
cycles are available on request.
Switching frequency:
ACS 100/140: Standard 4 kHz, Low-noise 8 kHz, silent 16 kHzNew
ACS 400 : Standard 4 kHz, Low-noise 8 kHz
Acceleration time : 0.1 to 1800 s
Deceleration time : 0.1 to 1800 s
Programmable control connections
Two analogue inputs (only one in ACS 100):
- Voltage signal : 0 (2) to 10 V, 200 kΩ single-ended
- Current signal : 0 (4) to 20 mA, 500 Ω single-ended
- Potentiometer reference value:
10 V ±2% max.
10 mA, 1kΩ ≤ R ≤ 10
kΩ
- Response time : ≤ 60 ms
- Resolution :
0.1%
- Accuracy :
±1%
In ACS140/400 one
analog output:
0 (4) to 20 mA, load
< 500 Ω
Auxiliary voltage : 12 V DC, max. 100 mA,
in ACS 400 24 V, max. 250 mA
Five digital inputs(only three in ACS100):
- 12 V...24 V DC with internal or external supply, PNP and NPN
- In ACS 100 ABB standard, 3-wire or alternate
- Input impedance: 1.5 kΩ
Response time : ≤ 9 ms
Two relay outputs
(only one fault relay in ACS 100):
- Switching voltage: 12 to 250 V AC or max 30 V DC/0.5 A
- Maximum continuous current: 10 mA to 2 A
Serial communication for the control panel or external control :
Modbus protocol |
Environmental limits
Ambient temperatures:
- Output current = I2, fswitch = 4 kHz: 0 to 40
◦C
ACS 100/140 additionally:
- Output current = 0.8 . I2, fswitch = 4
kHz: 40 to 50 ◦C
- Output current = I2, fswitch = 8 kHz: 0 to 30
◦C
- Output current = 0.9 . I2, fswitch
= 4 kHz: 40 to 50 ◦C
- Output current = 0.75. I2, fswitch = 16
kHz: o to 30 ◦C1)
ACS400 additionally:
- Output current = 0.9 I2, fswitch = 4
kHz: 40 to 50◦C
- Output current = 0.8 . I2, fswitch= 8 kHz: 0
to 40◦C
Altitude:
- Output current = I2 , 0 to 1000
- Output current reduced by 1% per 100 m over
1000 m to 2000 m
Relative humidity : lower than 95% (without condensation)
Protection class:
ACS 100/140 : IP 20
ACS 400/: IP 21 or IP 54
Paint colour : NCS 1502-Y, RAL 9002, PMS 420 C
Contamination levels : no conductive dust, corrosive liquids or
gases (IEC 721-3-3).
Product compliance
- Low Voltage Directive 73/23/EEC with supplements
- EMC Directive 89/336/EEC with supplements
- Quality assurance system ISO 9001 and ISO 14001
- CE, UL, ULc and C-Tick approvals
Options
- Extension cable 3 m with IP 65 Kit for control panels PEC-98-0008
- EMC input filters are required only in First Environment
- Braking units and choppers
- Motor and line chokes
ACS140/400:
- RS 485/232 adapter
- Drive Window Light
ACS400 :
- Control panel ACS-PAN-A
- Control panel ACS100-PAN
- DDCS adapter for fieldbus modules
1) Except ACS 143-1K1-3 and
ACS 143-2K1-3 where output current = 0.55 x I2, fSWITCH
=16kHz : 0 to 30 ◦C
|
